The cart is empty.

USA EN

Mexico EN | ES

English English Español English Français

You are here: Product Overview > 3.5 Controlling, Venting, Sealing of Liquids and Gases > Fluid Level Indicators > EN 656 Fluid Level Indicators previous product next product

EN 656 Fluid Level Indicators Plastic, with Electrical Fluid Level Monitoring, Axial Plug

Photo

EN 656 Plastic Fluid Level Indicators, with Electrical Fluid Level Monitoring, Axial Plug

ELESA original design
code: HCV-E-AX

Standard Sheet EN 656 Print This Page List of Fluid Level Indicator Types IP Protection Classes Plug Characteristics, Fluid Level Monitoring & Assembly Instructions for the Cable Connection Plastic Characteristics

Product description

Information

With fluid level indicators EN 656, the fluid level can not only be viewed, it can also be monitored using an electric contact.

A float with a magnet is located within the indication range which closes or opens a contact at a certain fluid level (REED switch).

The table values for the maximum allowable pressure are based on the use of mineral oil (according to ISO 3498) at a temperature of 73 °F (23 °C). Use under different conditions will influence the compressive strength and requires prior consultation.

Specification

Body
Plastic
Crystal clear polyamide (PA-T)

Aging resistant
High mechanical strength
Temperature resistant up to 194 °F (90 °C)
Solvent resistant,
but not alcohol resistant
Avoid contact with hot water

Contrast screen
White painted aluminum

Float
Plastic (Polyamide PA), black

Glass fiber reinforced
With built-in magnet

O-rings
Rubber NBR (Perbunan®)

Set screw, hex nut, serrated washer
Steel, zinc plated, blue passivated finish

RoHS

Technical drawing

EN 656 Plastic Fluid Level Indicators, with Electrical Fluid Level Monitoring, Axial Plug sketch

Hide technical drawing

Part Options / Table

Type

LS	With normally open contact
LO	With normally closed contact
LW	With change-over contact

Show / Hide columns

Metric

Dimensions in: Inch (change to Metric)

l₁	b	d Thread	h	k	l₂	l₃	l₄	l₅	l₆	l₇	l₈	l₉	s ≈ Max. wall thickness	Max. compressive strength in bar

5.00	1.22	M 12	1.18	1.97	0.86	3.82	6.79	0.59	1.10	0.79	1.14	1.00	0.31	18

Build & Price

3D Product Configurator

Distance of the screws l₁

5.00

Type

LO - With normally closed contact

LS - With normally open contact

LW - With change-over contact

Plug Characteristics


Connector:						DIN EN 175301-803 Type C
Cable fitting:						PG 7, for a cable diameter of 6 to 7 mm
Cable cross section:						max. 1.5 mm²
Protection class:						IP 65
Notice: Magnetic fields can cause interference!
$MD656{St:_}SB-36968-0$

Fluid Level Monitoring

The fluid level is measured by means of a float with a built-in magnet which opens or closes a contact (REED switch) when the minimum fluid level is reached.

Electrical details

Type LS (Normally open)

Type LO (Normally closed)

Type LW (Changeover contact)

Maximum contact voltage:

140 V AC, 200 V DC

140 V AC, 150 V DC

Maximum current on contact:

1.2 A

2 A

Maximum switch capacity:

10 W

20 W

Operating symbol:

$MD656{St:_}SB-41549-0$

$MD656{St:_}SB-41551-0$

$MD656{St:_}SB-41553-0$

Assembly Instructions for the Cable Connection

Loosen mounting screw and remove connector plug.
Push the contact insert out of the connector housing.
Loosen cable fitting, slip the cable through the connector housing, and connect the wires to the contact insert.
Push the contact insert back into the connector housing in the required position, tighten the cable fitting to relieve strain and to seal the cable.
Push the connector plug onto the contacts of the fluid lever indicator and then secure it with the mounting screw.

$MD656{St:_}MT-38795-0$

Selected Part

Part Number

Total Canadian Dollars (net)

Can$192.40

Call / Email for Delivery Time

Quantity

Please note our quantity discounts (Canadian Dollars).

Min	Max	Price
1	5	Can$192.40
6	49	Can$185.40
50	99	Can$174.91
≥ 100		Can$157.42

Prop 65: Not compliant

WARNING:
Cancer and Reproductive Harm - www.P65Warnings.ca.gov

RoHS: Compliant

This article is RoHS-compliant in application of Annex III., which means it complies with EU Directive 2011/65/EU, including extension (2015/863/EU), for restricting the use of certain hazardous substances in electrical and electronic devices. The Directive regulates the use of hazardous substances in devices and components. The implementation in national law is summarily described with RoHS(Restriction of (the use of certain) hazardous substances)).

Weight: 0.410 lbs

If weight is not listed, please contact our Sales Department for additional information regarding weight.
Phone: 1-800-397-6993

All Prices are in Canadian Dollars. Taxes Not Included.